Twist

mbelshe@chromium.org

Google, Inc

fenix@google.com

Microsoft

3210 Porter Drive Palo Alto 94304 US martin.thomson@skype.net

Isode Ltd

5 Castle Business Village 36 Station Road Hampton Middlesex TW12 2BX UK Alexey.Melnikov@isode.com

Applications HTTPbis Working Group HTTP SPDY Web This specification describes an optimized expression of the syntax of the Hypertext Transfer Protocol (HTTP). The HTTP/2.0 encapsulation enables more efficient use of network resources and reduced perception of latency by allowing header field compression and multiple concurrent messages on the same connection. It also introduces unsolicited push of representations from servers to clients. This document is an alternative to, but does not obsolete the HTTP/1.1 message format or protocol. HTTP's existing semantics remain unchanged. Discussion of this draft takes place on the HTTPBIS working group mailing list (ietf-http-wg@w3.org), which is archived at . Working Group information and related documents can be found at (Wiki) and (source code and issues tracker). The changes in this draft are summarized in .

The Hypertext Transfer Protocol (HTTP) is a wildly successful protocol. However, the HTTP/1.1 message format () is optimized for implementation simplicity and accessibility, not application performance. As such it has several characteristics that have a negative overall effect on application performance. In particular, HTTP/1.0 only allows one request to be delivered at a time on a given connection. HTTP/1.1 pipelining only partially addressed request concurrency, and is not widely deployed. Therefore, clients that need to make many requests (as is common on the Web) typically use multiple connections to a server in order to reduce perceived latency. Furthermore, HTTP/1.1 header fields are often repetitive and verbose, which, in addition to generating more or larger network packets, can cause the small initial TCP congestion window to quickly fill. This can result in excessive latency when multiple requests are made on a single new TCP connection. This document addresses these issues by defining an optimized mapping of HTTP's semantics to an underlying connection. Specifically, it allows interleaving of request and response messages on the same connection and uses an efficient coding for HTTP header fields. It also allows prioritization of requests, letting more important requests complete more quickly, further improving perceived performance. The resulting protocol is designed to be more friendly to the network, because fewer TCP connections can be used, in comparison to HTTP/1.x. This means less competition with other flows, and longer-lived connections, which in turn leads to better utilization of available network capacity. Finally, this encapsulation also enables more scalable processing of messages through use of binary message framing.

The HTTP/2.0 Specification is split into three parts: starting HTTP/2.0, which covers how a HTTP/2.0 connection is initiated; a framing layer, which multiplexes a single TCP connection into independent frames of various types; and an HTTP layer, which specifies the mechanism for expressing HTTP interactions using the framing layer. While some of the framing layer concepts are isolated from HTTP, building a generic framing layer has not been a goal. The framing layer is tailored to the needs of the HTTP protocol and server push.

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119. All numeric values are in network byte order. Values are unsigned unless otherwise indicated. Literal values are provided in decimal or hexadecimal as appropriate. Hexadecimal literals are prefixed with 0x to distinguish them from decimal literals. The following terms are used: The endpoint initiating the HTTP connection. A transport-level connection between two endpoints. Either the client or server of the connection. The smallest unit of communication within an HTTP/2.0 connection, consisting of a header and a variable-length sequence of bytes structured according to the frame type. An endpoint. When discussing a particular endpoint, "peer" refers to the endpoint that is remote to the primary subject of discussion. An endpoint that is receiving frames. An endpoint that is transmitting frames. The endpoint which did not initiate the HTTP connection. An error on the HTTP/2.0 connection. A bi-directional flow of frames across a virtual channel within the HTTP/2.0 connection. An error on the individual HTTP/2.0 stream.

HTTP/2.0 provides an optimized transport for HTTP semantics. An HTTP/2.0 connection is an application level protocol running on top of a TCP connection (). The client is the TCP connection initiator. This document describes the HTTP/2.0 protocol using a logical structure that is formed of three parts: framing, streams, and application mapping. This structure is provided primarily as an aid to specification, implementations are free to diverge from this structure as necessary.

HTTP/2.0 provides an efficient serialization of HTTP semantics. HTTP requests and responses are encoded into length-prefixed frames (see ). HTTP headers are compressed into a series of frames that contain header block fragments (see ).

HTTP/2.0 provides the ability to multiplex multiple HTTP requests and responses onto a single connection. Multiple requests or responses can be sent concurrently on a connection using streams. In order to maintain independent streams, flow control and prioritization are necessary.

HTTP/2.0 defines how HTTP requests and responses are mapped to streams (see ) and introduces a new interaction model, server push.

HTTP/2.0 uses the same "http" and "https" URI schemes used by HTTP/1.1. HTTP/2.0 shares the same default port numbers: 80 for "http" URIs and 443 for "https" URIs. As a result, implementations processing requests for target resource URIs like http://example.org/foo or https://example.com/bar are required to first discover whether the upstream server (the immediate peer to which the client wishes to establish a connection) supports HTTP/2.0. The means by which support for HTTP/2.0 is determined is different for "http" and "https" URIs. Discovery for "http" URIs is described in . Discovery for "https" URIs is described in .

The protocol defined in this document is identified using the string "HTTP/2.0". This identification is used in the HTTP/1.1 Upgrade header field, in the TLS application layer protocol negotiation extension field, and other places where protocol identification is required. Negotiating "HTTP/2.0" implies the use of the transport, security, framing and message semantics described in this document. Editor's Note: please remove the remainder of this section prior to the publication of a final version of this document. Only implementations of the final, published RFC can identify themselves as "HTTP/2.0". Until such an RFC exists, implementations MUST NOT identify themselves using "HTTP/2.0". Examples and text throughout the rest of this document use "HTTP/2.0" as a matter of editorial convenience only. Implementations of draft versions MUST NOT identify using this string. The exception to this rule is the string included in the connection header sent by clients immediately after establishing an HTTP/2.0 connection (see ); this fixed length sequence of octets does not change. Implementations of draft versions of the protocol MUST add the string "-draft-" and the corresponding draft number to the identifier before the separator ('/'). For example, draft-ietf-httpbis-http2-03 is identified using the string "HTTP-draft-03/2.0". Non-compatible experiments that are based on these draft versions MUST instead replace the string "draft" with a different identifier. For example, an experimental implementation of packet mood-based encoding based on draft-ietf-httpbis-http2-07 might identify itself as "HTTP-emo-07/2.0". Note that any label MUST conform to the "token" syntax defined in . Experimenters are encouraged to coordinate their experiments on the ietf-http-wg@w3.org mailing list.

A client that makes a request to an "http" URI without prior knowledge about support for HTTP/2.0 uses the HTTP Upgrade mechanism (). The client makes an HTTP/1.1 request that includes an Upgrade header field identifying HTTP/2.0. The HTTP/1.1 request MUST include exactly one HTTP2-Settings header field.

For example: GET /default.htm HTTP/1.1 Host: server.example.com Connection: Upgrade, HTTP2-Settings Upgrade: HTTP/2.0 HTTP2-Settings: <base64url encoding of HTTP/2.0 SETTINGS payload>

Requests that contain a request entity body MUST be sent in their entirety before the client can send HTTP/2.0 frames. This means that a large request entity can block the use of the connection until it is completely sent. If concurrency of an initial request with subsequent requests is important, a small request can be used to perform the upgrade to HTTP/2.0, at the cost of an additional round trip. A server that does not support HTTP/2.0 can respond to the request as though the Upgrade header field were absent:

HTTP/1.1 200 OK Content-length: 243 Content-type: text/html ...

A server that supports HTTP/2.0 accepts the upgrade with a 101 (Switching Protocols) status code. After the empty line that terminates the 101 response, the server can begin sending HTTP/2.0 frames. These frames MUST include a response to the request that initiated the Upgrade.

HTTP/1.1 101 Switching Protocols Connection: Upgrade Upgrade: HTTP/2.0 [ HTTP/2.0 connection ...

The first HTTP/2.0 frame sent by the server is a SETTINGS frame (). Upon receiving the 101 response, the client sends a connection header, which includes a SETTINGS frame. The HTTP/1.1 request that is sent prior to upgrade is associated with stream 1 and is assigned the highest possible priority. Stream 1 is implicitly half closed from the client toward the server, since the request is completed as an HTTP/1.1 request. After commencing the HTTP/2.0 connection, stream 1 is used for the response.

A client that upgrades from HTTP/1.1 to HTTP/2.0 MUST include exactly one HTTP2-Settings header field. The HTTP2-Settings header field is a hop-by-hop header field that includes settings that govern the HTTP/2.0 connection, provided in anticipation of the server accepting the request to upgrade. A server MUST reject an attempt to upgrade if this header is not present.

The content of the HTTP2-Settings header field is the payload of a SETTINGS frame (), encoded as a base64url string (that is, the URL- and filename-safe Base64 encoding described in , with any trailing '=' characters omitted). The ABNF production for token68 is defined in . The client MUST include values for the following settings: SETTINGS_MAX_CONCURRENT_STREAMS SETTINGS_INITIAL_WINDOW_SIZE As a hop-by-hop header field, the Connection header field MUST include a value of HTTP2-Settings in addition to Upgrade when upgrading to HTTP/2.0. A server decodes and interprets these values as it would any other SETTINGS frame. Providing these values in the Upgrade request ensures that the protocol does not require default values for the above settings, and gives a client an opportunity to provide other settings prior to receiving any frames from the server.

A client that makes a request to an "https" URI without prior knowledge about support for HTTP/2.0 uses TLS with the application layer protocol negotiation extension. Once TLS negotiation is complete, both the client and the server send a connection header.

A client can learn that a particular server supports HTTP/2.0 by other means. A client MAY immediately send HTTP/2.0 frames to a server that is known to support HTTP/2.0, after the connection header. This only affects the resolution of "http" URIs; servers supporting HTTP/2.0 are required to support protocol negotiation in TLS for "https" URIs. Prior support for HTTP/2.0 is not a strong signal that a given server will support HTTP/2.0 for future connections. It is possible for server configurations to change or for configurations to differ between instances in clustered server. Interception proxies (a.k.a. "transparent" proxies) are another source of variability.

Upon establishment of a TCP connection and determination that HTTP/2.0 will be used by both peers, each endpoint MUST send a connection header as a final confirmation and to establish the initial settings for the HTTP/2.0 connection. The client connection header is a sequence of 24 octets, which in hex notation are:

(the string PRI * HTTP/2.0\r\n\r\nSM\r\n\r\n) followed by a SETTINGS frame (). The client sends the client connection header immediately upon receipt of a 101 Switching Protocols response (indicating a successful upgrade), or as the first application data octets of a TLS connection. If starting an HTTP/2.0 connection with prior knowledge of server support for the protocol, the client connection header is sent upon connection establishment. The client connection header is selected so that a large proportion of HTTP/1.1 or HTTP/1.0 servers and intermediaries do not attempt to process further frames. Note that this does not address the concerns raised in . The server connection header consists of just a SETTINGS frame () that MUST be the first frame the server sends in the HTTP/2.0 connection. To avoid unnecessary latency, clients are permitted to send additional frames to the server immediately after sending the client connection header, without waiting to receive the server connection header. It is important to note, however, that the server connection header SETTINGS frame might include parameters that necessarily alter how a client is expected to communicate with the server. Upon receiving the SETTINGS frame, the client is expected to honor any parameters established. Clients and servers MUST terminate the TCP connection if either peer does not begin with a valid connection header. A GOAWAY frame () MAY be omitted if it is clear that the peer is not using HTTP/2.0.

Once the HTTP/2.0 connection is established, endpoints can begin exchanging frames.

All frames begin with an 8-octet header followed by a payload of between 0 and 65,535 octets.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Length (16) | Type (8) | Flags (8) | +-+-------------+---------------+-------------------------------+ |R| Stream Identifier (31) | +-+-------------------------------------------------------------+ | Frame Payload (0...) ... +---------------------------------------------------------------+

The fields of the frame header are defined as: The length of the frame payload expressed as an unsigned 16-bit integer. The 8 octets of the frame header are not included in this value. The 8-bit type of the frame. The frame type determines how the remainder of the frame header and payload are interpreted. Implementations MUST ignore frames of unsupported or unrecognized types. An 8-bit field reserved for frame-type specific boolean flags. Flags are assigned semantics specific to the indicated frame type. Flags that have no defined semantics for a particular frame type MUST be ignored, and MUST be left unset (0) when sending. A reserved 1-bit field. The semantics of this bit are undefined and the bit MUST remain unset (0) when sending and MUST be ignored when receiving. A 31-bit stream identifier (see ). A value 0 is reserved for frames that are associated with the connection as a whole as opposed to an individual stream. The structure and content of the frame payload is dependent entirely on the frame type.

The maximum size of a frame payload varies by frame type and use. The absolute maximum size is 65,535 octets. All implementations SHOULD be capable of receiving and minimally processing frames up to this size. Certain frame types, such as PING (see ), impose additional limits on the amount of payload data allowed. Likewise, additional size limits can be set by specific application uses (see ). If a frame size exceeds any defined limit, or is too small to contain mandatory frame data, the endpoint MUST send a FRAME_TOO_LARGE error. Frame size errors in frames that affect connection-level state MUST be treated as a connection error.

A header in HTTP/2.0 is a name-value pair with one or more associated values. They are used within HTTP request and response messages as well as server push operations (see ). Header sets are logical collections of zero or more header fields arranged at the application layer. When transmitted over a connection, the header set is serialized into a header block using HTTP Header Compression. The serialized header block is then divided into one or more octet sequences, called header block fragments, and transmitted within the payload of HEADERS, PUSH_PROMISE or CONTINUATION frames. The receiving endpoint reassembles the header block by concatenating the individual fragments, then decompresses the block to reconstruct the header set. Header block fragments can only be sent as the payload of HEADERS, PUSH_PROMISE or CONTINUATION frames. A compressed and encoded header block is transmitted in a HEADERS or PUSH_PROMISE frame, followed by zero or more CONTINUATION frames. If the number of octets in the block is greater than the space remaining in the frame, the block is divided into multiple fragments, which are then transmitted in multiple frames. Header blocks MUST be transmitted as a contiguous sequence of frames, with no interleaved frames of any other type, or from any other stream. The last frame in a sequence of HEADERS/CONTINUATION frames MUST have the END_HEADERS flag set. The last frame in a sequence of PUSH_PROMISE/CONTINUATION frames MUST have the END_PUSH_PROMISE/END_HEADERS flag set (respectively). HEADERS, PUSH_PROMISE and CONTINUATION frames carry data that can modify the compression context maintained by a receiver. An endpoint receiving HEADERS, PUSH_PROMISE or CONTINUATION frames MUST reassemble header blocks and perform decompression even if the frames are to be discarded, which is likely to occur after a stream is reset. A receiver MUST terminate the connection with a connection error of type COMPRESSION_ERROR, if it does not decompress a header block.

A "stream" is an independent, bi-directional sequence of HEADERS and DATA frames exchanged between the client and server within an HTTP/2.0 connection. Streams have several important characteristics: A single HTTP/2.0 connection can contain multiple concurrently active streams, with either endpoint interleaving frames from multiple streams. Streams can be established and used unilaterally or shared by either the client or server. Streams can be closed by either endpoint. The order in which frames are sent within a stream is significant. Recipients process frames in the order they are received. Streams are identified by an integer. Stream identifiers are assigned to streams by the endpoint that initiates a stream.

The lifecycle of a stream is shown in .

| |<-----------' | | R | closed | R | `-------------------->| |<--------------------' +--------+ ]]>

Both endpoints have a subjective view of the state of a stream that could be different when frames are in transit. Endpoints do not coordinate the creation of streams, they are created unilaterally by either endpoint. The negative consequences of a mismatch in states are limited to the "closed" state after sending RST_STREAM, where frames might be received for some time after closing. Streams have the following states: All streams start in the "idle" state. In this state, no frames have been exchanged. The following transitions are valid from this state: Sending or receiving a HEADERS frame causes the stream to become "open". The stream identifier is selected as described in . Sending a PUSH_PROMISE frame marks the associated stream for later use. The stream state for the reserved stream transitions to "reserved (local)". Receiving a PUSH_PROMISE frame marks the associated stream as reserved by the remote peer. The state of the stream becomes "reserved (remote)". A stream in the "reserved (local)" state is one that has been promised by sending a PUSH_PROMISE frame. A PUSH_PROMISE frame reserves an idle stream by associating the stream with an open stream that was initiated by the remote peer (see ). In this state, only the following transitions are possible: The endpoint can send a HEADERS frame. This causes the stream to open in a "half closed (remote)" state. Either endpoint can send a RST_STREAM frame to cause the stream to become "closed". This also releases the stream reservation. An endpoint MUST NOT send any other type of frame in this state. Receiving any frame other than RST_STREAM or PRIORITY MUST be treated as a connection error of type PROTOCOL_ERROR. A stream in the "reserved (remote)" state has been reserved by a remote peer. In this state, only the following transitions are possible: Receiving a HEADERS frame causes the stream to transition to "half closed (local)". Either endpoint can send a RST_STREAM frame to cause the stream to become "closed". This also releases the stream reservation. Receiving any other type of frame MUST be treated as a stream error of type PROTOCOL_ERROR. An endpoint MAY send RST_STREAM or PRIORITY frames in this state to cancel or reprioritize the reserved stream. The "open" state is where both peers can send frames of any type. In this state, sending peers observe advertised stream level flow control limits. From this state either endpoint can send a frame with a END_STREAM flag set, which causes the stream to transition into one of the "half closed" states: an endpoint sending a END_STREAM flag causes the stream state to become "half closed (local)"; an endpoint receiving a END_STREAM flag causes the stream state to become "half closed (remote)". Either endpoint can send a RST_STREAM frame from this state, causing it to transition immediately to "closed". A stream that is "half closed (local)" cannot be used for sending frames. A stream transitions from this state to "closed" when a frame that contains a END_STREAM flag is received, or when either peer sends a RST_STREAM frame. A receiver can ignore WINDOW_UPDATE or PRIORITY frames in this state. These frame types might arrive for a short period after a frame bearing the END_STREAM flag is sent. A stream that is "half closed (remote)" is no longer being used by the peer to send frames. In this state, an endpoint is no longer obligated to maintain a receiver flow control window if it performs flow control. If an endpoint receives additional frames for a stream that is in this state it MUST respond with a stream error of type STREAM_CLOSED. A stream can transition from this state to "closed" by sending a frame that contains a END_STREAM flag, or when either peer sends a RST_STREAM frame. The "closed" state is the terminal state. An endpoint MUST NOT send frames on a closed stream. An endpoint that receives a frame after receiving a RST_STREAM or a frame containing a END_STREAM flag on that stream MUST treat that as a stream error of type STREAM_CLOSED. WINDOW_UPDATE or PRIORITY frames can be received in this state for a short period after a a frame containing an END_STREAM flag is sent. Until the remote peer receives and processes the frame bearing the END_STREAM flag, it might send either frame type. Endpoints MUST ignore WINDOW_UPDATE frames received in this state, though endpoints MAY choose to treat WINDOW_UPDATE frames that arrive a significant time after sending END_STREAM as a connection error of type PROTOCOL_ERROR. If this state is reached as a result of sending a RST_STREAM frame, the peer that receives the RST_STREAM might have already sent - or enqueued for sending - frames on the stream that cannot be withdrawn. An endpoint MUST ignore frames that it receives on closed streams after it has sent a RST_STREAM frame. An endpoint MAY choose to limit the period over which it ignores frames and treat frames that arrive after this time as being in error. Flow controlled frames (i.e., DATA) received after sending RST_STREAM are counted toward the connection flow control window. Even though these frames might be ignored, because they are sent before the sender receives the RST_STREAM, the sender will consider the frames to count against the flow control window. An endpoint might receive a PUSH_PROMISE or a CONTINUATION frame after it sends RST_STREAM. PUSH_PROMISE causes a stream to become "reserved". If promised streams are not desired, a RST_STREAM can be used to close any of those streams. In the absence of more specific guidance elsewhere in this document, implementations SHOULD treat the receipt of a message that is not expressly permitted in the description of a state as a connection error of type PROTOCOL_ERROR.

Streams are identified with an unsigned 31-bit integer. Streams initiated by a client MUST use odd-numbered stream identifiers; those initiated by the server MUST use even-numbered stream identifiers. A stream identifier of zero (0x0) is used for connection control message; the stream identifier zero MUST NOT be used to establish a new stream. A stream identifier of one (0x1) is used to respond to the HTTP/1.1 request which was specified during Upgrade (see ); the stream identifier one MUST NOT be used to establish a new stream. The identifier of a newly established stream MUST be numerically greater than all streams that the initiating endpoint has opened or reserved. This governs streams that are opened using a HEADERS frame and streams that are reserved using PUSH_PROMISE. An endpoint that receives an unexpected stream identifier MUST respond with a connection error of type PROTOCOL_ERROR. The first use of a new stream identifier implicitly closes all idle streams that might have been initiated by that peer with a lower-valued stream identifier. Stream identifiers cannot be reused. Long-lived connections can result in endpoint exhausting the available range of stream identifiers. A client that is unable to establish a new stream identifier can establish a new connection for new streams.

A peer can limit the number of concurrently active streams using the SETTINGS_MAX_CONCURRENT_STREAMS parameters within a SETTINGS frame. The maximum concurrent streams setting is specific to each endpoint and applies only to the peer that receives the setting. That is, clients specify the maximum number of concurrent streams the server can initiate, and servers specify the maximum number of concurrent streams the client can initiate. Endpoints MUST NOT exceed the limit set by their peer. Streams that are in the "open" state, or either of the "half closed" states count toward the maximum number of streams that an endpoint is permitted to open. Streams in any of these three states count toward the limit advertised in the SETTINGS_MAX_CONCURRENT_STREAMS setting (see ). Streams in either of the "reserved" states do not count as open, even if a small amount of application state is retained to ensure that the promised stream can be successfully used.

Using streams for multiplexing introduces contention over use of the TCP connection, resulting in blocked streams. A flow control scheme ensures that streams on the same connection do not destructively interfere with each other. Flow control is used for both individual streams and for the connection as a whole. HTTP/2.0 provides for flow control through use of the WINDOW_UPDATE frame type.

Experience with TCP congestion control has shown that algorithms can evolve over time to become more sophisticated without requiring protocol changes. TCP congestion control and its evolution is clearly different from HTTP/2.0 flow control, though the evolution of TCP congestion control algorithms shows that a similar approach could be feasible for HTTP/2.0 flow control. HTTP/2.0 stream flow control aims to allow for future improvements to flow control algorithms without requiring protocol changes. Flow control in HTTP/2.0 has the following characteristics: Flow control is hop-by-hop, not end-to-end. Flow control is based on window update frames. Receivers advertise how many bytes they are prepared to receive on a stream and for the entire connection. This is a credit-based scheme. Flow control is directional with overall control provided by the receiver. A receiver MAY choose to set any window size that it desires for each stream and for the entire connection. A sender MUST respect flow control limits imposed by a receiver. Clients, servers and intermediaries all independently advertise their flow control preferences as a receiver and abide by the flow control limits set by their peer when sending. The initial value for the flow control window is 65535 bytes for both new streams and the overall connection. The frame type determines whether flow control applies to a frame. Of the frames specified in this document, only DATA frames are subject to flow control; all other frame types do not consume space in the advertised flow control window. This ensures that important control frames are not blocked by flow control. Flow control can be disabled by a receiver. A receiver can choose to disable both forms of flow control by sending the SETTINGS_FLOW_CONTROL_OPTIONS setting. See Ending Flow Control for more details. HTTP/2.0 standardizes only the format of the WINDOW_UPDATE frame (). This does not stipulate how a receiver decides when to send this frame or the value that it sends. Nor does it specify how a sender chooses to send packets. Implementations are able to select any algorithm that suits their needs. Implementations are also responsible for managing how requests and responses are sent based on priority; choosing how to avoid head of line blocking for requests; and managing the creation of new streams. Algorithm choices for these could interact with any flow control algorithm.

Flow control is defined to protect endpoints that are operating under resource constraints. For example, a proxy needs to share memory between many connections, and also might have a slow upstream connection and a fast downstream one. Flow control addresses cases where the receiver is unable process data on one stream, yet wants to continue to process other streams in the same connection. Deployments that do not require this capability SHOULD disable flow control for data that is being received. Note that flow control cannot be disabled for sending. Sending data is always subject to the flow control window advertised by the receiver. Deployments with constrained resources (for example, memory) MAY employ flow control to limit the amount of memory a peer can consume. Note, however, that this can lead to suboptimal use of available network resources if flow control is enabled without knowledge of the bandwidth-delay product (see ). Even with full awareness of the current bandwidth-delay product, implementation of flow control can be difficult. When using flow control, the receive MUST read from the TCP receive buffer in a timely fashion. Failure to do so could lead to a deadlock when critical frames, such as WINDOW_UPDATE, are not available to HTTP/2.0. However, flow control can ensure that constrained resources are protected without any reduction in connection utilization.

The endpoint establishing a new stream can assign a priority for the stream. Priority is represented as an unsigned 31-bit integer. 0 represents the highest priority and 231-1 represents the lowest priority. The purpose of this value is to allow an endpoint to express the relative priority of a stream. An endpoint can use this information to preferentially allocate resources to a stream. Within HTTP/2.0, priority can be used to select streams for transmitting frames when there is limited capacity for sending. For instance, an endpoint might enqueue frames for all concurrently active streams. As transmission capacity becomes available, frames from higher priority streams might be sent before lower priority streams. Explicitly setting the priority for a stream does not guarantee any particular processing or transmision order for the stream relative to any other stream. Nor is there any mechanism provided by which the initiator of a stream can force or require a receiving endpoint to process concurrent streams in a particular order. Unless explicitly specified in the HEADERS frame () during stream creation, the default stream priority is 230. Pushed streams have a lower priority than their associated stream. The promised stream inherits the priority value of the associated stream plus one, up to a maximum of 231-1.

HTTP/2.0 framing permits two classes of error: An error condition that renders the entire connection unusable is a connection error. An error in an individual stream is a stream error. A list of error codes is included in .

A connection error is any error which prevents further processing of the framing layer or which corrupts any connection state. An endpoint that encounters a connection error SHOULD first send a GOAWAY frame () with the stream identifier of the last stream that it successfully received from its peer. The GOAWAY frame includes an error code that indicates why the connection is terminating. After sending the GOAWAY frame, the endpoint MUST close the TCP connection. It is possible that the GOAWAY will not be reliably received by the receiving endpoint. In the event of a connection error, GOAWAY only provides a best-effort attempt to communicate with the peer about why the connection is being terminated. An endpoint can end a connection at any time. In particular, an endpoint MAY choose to treat a stream error as a connection error. Endpoints SHOULD send a GOAWAY frame when ending a connection, as long as circumstances permit it.

A stream error is an error related to a specific stream identifier that does not affect processing of other streams. An endpoint that detects a stream error sends a RST_STREAM frame () that contains the stream identifier of the stream where the error occurred. The RST_STREAM frame includes an error code that indicates the type of error. A RST_STREAM is the last frame that an endpoint can send on a stream. The peer that sends the RST_STREAM frame MUST be prepared to receive any frames that were sent or enqueued for sending by the remote peer. These frames can be ignored, except where they modify connection state (such as the state maintained for header compression). Normally, an endpoint SHOULD NOT send more than one RST_STREAM frame for any stream. However, an endpoint MAY send additional RST_STREAM frames if it receives frames on a closed stream after more than a round trip time. This behavior is permitted to deal with misbehaving implementations. An endpoint MUST NOT send a RST_STREAM in response to an RST_STREAM frame, to avoid looping.

If the TCP connection is torn down while streams remain in open or half closed states, then the endpoint MUST assume that the stream was abnormally interrupted and could be incomplete.

This specification defines a number of frame types, each identified by a unique 8-bit type code. Each frame type serves a distinct purpose either in the establishment and management of the connection as a whole, or of individual streams. The transmission of specific frame types can alter the state of a connection. If endpoints fail to maintain a synchronized view of the connection state, successful communication within the connection will no longer be possible. Therefore, it is important that endpoints have a shared comprehension of how the state is affected by the use any given frame. Accordingly, while it is expected that new frame types will be introduced by extensions to this protocol, only frames defined by this document are permitted to alter the connection state.

DATA frames (type=0x0) convey arbitrary, variable-length sequences of octets associated with a stream. One or more DATA frames are used, for instance, to carry HTTP request or response payloads. The DATA frame defines the following flags: Bit 1 being set indicates that this frame is the last that the endpoint will send for the identified stream. Setting this flag causes the stream to enter a "half closed" or "closed" state. Bit 2 is reserved for future use. DATA frames MUST be associated with a stream. If a DATA frame is received whose stream identifier field is 0x0, the recipient MUST respond with a connection error of type PROTOCOL_ERROR. DATA frames are subject to flow control and can only be sent when a stream is in the "open" or "half closed (remote)" states.

The HEADERS frame (type=0x1) carries name-value pairs. It is used to open a stream. HEADERS frames can be sent on a stream in the "open" or "half closed (remote)" states.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X| Priority (31) | +-+-------------------------------------------------------------+ | Header Block Fragment (*) ... +---------------------------------------------------------------+

The HEADERS frame defines the following flags: Bit 1 being set indicates that this frame is the last that the endpoint will send for the identified stream. Setting this flag causes the stream to enter a "half closed" state. Bit 2 is reserved for future use. The END_HEADERS bit indicates that this frame ends the sequence of header block fragments necessary to provide a complete set of headers. The payload for a complete header block is provided by a sequence of that starts with a HEADERS frame, followed by zero or more CONTINUATION frames. The sequence is terminated by a frame with the END_HEADERS flag set. Once the sequence terminates, the payload of all HEADERS and CONTINUATION frames are concatenated and interpreted as a single block. A HEADERS frame without the END_HEADERS flag set MUST be followed by a CONTINUATION frame for the same stream. A receiver MUST treat the receipt of any other type of frame or a frame on a different stream as a connection error of type PROTOCOL_ERROR. Bit 4 being set indicates that the first four octets of this frame contain a single reserved bit and a 31-bit priority; see . If this bit is not set, the four bytes do not appear and the frame only contains a header block fragment. The payload of a HEADERS frame contains a header block fragment. A header block that does not fit within a HEADERS frame is continued in a CONTINUATION frame. HEADERS frames MUST be associated with a stream. If a HEADERS frame is received whose stream identifier field is 0x0, the recipient MUST respond with a connection error of type PROTOCOL_ERROR. The HEADERS frame changes the connection state as described in .

The PRIORITY frame (type=0x2) specifies the sender-advised priority of a stream. It can be sent at any time for an existing stream. This enables reprioritisation of existing streams.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X| Priority (31) | +-+-------------------------------------------------------------+

The payload of a PRIORITY frame contains a single reserved bit and a 31-bit priority. The PRIORITY frame does not define any flags. The PRIORITY frame is associated with an existing stream. If a PRIORITY frame is received with a stream identifier of 0x0, the recipient MUST respond with a connection error of type PROTOCOL_ERROR. The PRIORITY frame can be sent on a stream in any of the "reserved (remote)", "open", "half-closed (local)", or "half closed (remote)" states, though it cannot be sent between consecutive frames that comprise a single header block. Note that this frame could arrive after processing or frame sending has completed, which would cause it to have no effect. For a stream that is in the "half closed (remote)" state, this frame can only affect processing of the stream and not frame transmission.

The RST_STREAM frame (type=0x3) allows for abnormal termination of a stream. When sent by the initiator of a stream, it indicates that they wish to cancel the stream or that an error condition has occurred. When sent by the receiver of a stream, it indicates that either the receiver is rejecting the stream, requesting that the stream be cancelled or that an error condition has occurred.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Error Code (32) | +---------------------------------------------------------------+

The RST_STREAM frame contains a single unsigned, 32-bit integer identifying the error code. The error code indicates why the stream is being terminated. The RST_STREAM frame does not define any flags. The RST_STREAM frame fully terminates the referenced stream and causes it to enter the closed state. After receiving a RST_STREAM on a stream, the receiver MUST NOT send additional frames for that stream. However, after sending the RST_STREAM, the sending endpoint MUST be prepared to receive and process additional frames sent on the stream that might have been sent by the peer prior to the arrival of the RST_STREAM. RST_STREAM frames MUST be associated with a stream. If a RST_STREAM frame is received with a stream identifier of 0x0, the recipient MUST treat this as a connection error of type PROTOCOL_ERROR. RST_STREAM frames MUST NOT be sent for a stream in the "idle" state. If a RST_STREAM frame identifying an idle stream is received, the recipient MUST treat this as a connection error of type PROTOCOL_ERROR.

The SETTINGS frame (type=0x4) conveys configuration parameters that affect how endpoints communicate. The parameters are either constraints on peer behavior or preferences. SETTINGS frames MUST be sent at the start of a connection, and MAY be sent at any other time by either endpoint over the lifetime of the connection. Implementations MUST support all of the settings defined by this specification and MAY support additional settings defined by extensions. Unsupported or unrecognized settings MUST be ignored. New settings MUST NOT be defined or implemented in a way that requires endpoints to understand them in order to communicate successfully. Each setting in a SETTINGS frame replaces the existing value for that setting. Settings are processed in the order in which they appear, and a receiver of a SETTINGS frame does not need to maintain any state other than the current value of settings. Therefore, the value of a setting is the last value that is seen by a receiver. This permits the inclusion of the same settings multiple times in the same SETTINGS frame, though doing so does nothing other than waste connection capacity. The SETTINGS frame does not define any flags. SETTINGS frames always apply to a connection, never a single stream. The stream identifier for a settings frame MUST be zero. If an endpoint receives a SETTINGS frame whose stream identifier field is anything other than 0x0, the endpoint MUST respond with a connection error of type PROTOCOL_ERROR. The SETTINGS frame affects connection state. A badly formed or incomplete SETTINGS frame MUST be treated as a connection error of type PROTOCOL_ERROR.

The payload of a SETTINGS frame consists of zero or more settings. Each setting consists of an 8-bit reserved field, an unsigned 24-bit setting identifier, and an unsigned 32-bit value.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved (8) | Setting Identifier (24) | +---------------+-----------------------------------------------+ | Value (32) | +---------------------------------------------------------------+

The following settings are defined: indicates the maximum number of concurrent streams that the sender will allow. This limit is directional: it applies to the number of streams that the sender permits the receiver to create. By default there is no limit. It is recommended that this value be no smaller than 100, so as to not unnecessarily limit parallelism. indicates the sender's initial window size (in bytes) for stream level flow control. This settings affects the window size of all streams, including existing streams, see . indicates flow control options. The least significant bit (0x1) of the value is set to indicate that the sender has disabled all flow control. This bit cannot be cleared once set, see . All bits other than the least significant are reserved.

The PUSH_PROMISE frame (type=0x5) is used to notify the peer endpoint in advance of streams the sender intends to initiate. The PUSH_PROMISE frame includes the unsigned 31-bit identifier of the stream the endpoint plans to create along with a minimal set of headers that provide additional context for the stream. contains a thorough description of the use of PUSH_PROMISE frames.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X| Promised-Stream-ID (31) | +-+-------------------------------------------------------------+ | Header Block Fragment (*) ... +---------------------------------------------------------------+

The payload of a PUSH_PROMISE includes a "Promised-Stream-ID". This unsigned 31-bit integer identifies the stream the endpoint intends to start sending frames for. The promised stream identifier MUST be a valid choice for the next stream sent by the sender (see new stream identifier). Following the "Promised-Stream-ID" is a header block fragment. PUSH_PROMISE frames MUST be associated with an existing, peer-initiated stream. If the stream identifier field specifies the value 0x0, a recipient MUST respond with a connection error of type PROTOCOL_ERROR. The PUSH_PROMISE frame defines the following flags: The END_PUSH_PROMISE bit indicates that this frame ends the sequence of header block fragments necessary to provide a complete set of headers. The payload for a complete header block is provided by a sequence of PUSH_PROMISE frames, terminated by a PUSH_PROMISE frame with the END_PUSH_PROMISE flag set. Once the sequence terminates, the payload of all PUSH_PROMISE frames are concatenated and interpreted as a single block. A PUSH_PROMISE frame without the END_PUSH_PROMISE flag set MUST be followed by a PUSH_PROMISE frame for the same stream. A receiver MUST treat the receipt of any other type of frame or a frame on a different stream as a connection error of type PROTOCOL_ERROR. Promised streams are not required to be used in order promised. The PUSH_PROMISE only reserves stream identifiers for later use. Recipients of PUSH_PROMISE frames can choose to reject promised streams by returning a RST_STREAM referencing the promised stream identifier back to the sender of the PUSH_PROMISE. The PUSH_PROMISE frame modifies the connection state as defined in . A PUSH_PROMISE frame modifies the connection state in two ways. The inclusion of a header block potentially modifies the compression state. PUSH_PROMISE also reserves a stream for later use, causing the promised stream to enter the "reserved" state. A sender MUST NOT send a PUSH_PROMISE on a stream unless that stream is either "open" or "half closed (remote)"; the sender MUST ensure that the promised stream is a valid choice for a new stream identifier (that is, the promised stream MUST be in the "idle" state). Since PUSH_PROMISE reserves a stream, ignoring a PUSH_PROMISE frame causes the stream state to become indeterminate. A receiver MUST treat the receipt of a PUSH_PROMISE on a stream that is neither "open" nor "half-closed (local)" as a connection error of type PROTOCOL_ERROR. Similarly, a receiver MUST treat the receipt of a PUSH_PROMISE that promises an illegal stream identifier (that is, an identifier for a stream that is not currently in the "idle" state) as a connection error of type PROTOCOL_ERROR.

The PING frame (type=0x6) is a mechanism for measuring a minimal round-trip time from the sender, as well as determining whether an idle connection is still functional. PING frames can be sent from any endpoint.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Opaque Data (64) | | | +---------------------------------------------------------------+

In addition to the frame header, PING frames MUST contain 8 octets of data in the payload. A sender can include any value it chooses and use those bytes in any fashion. Receivers of a PING frame that does not include a PONG flag MUST send a PING frame with the PONG flag set in response, with an identical payload. PING responses SHOULD given higher priority than any other frame. The PING frame defines the following flags: Bit 1 being set indicates that this PING frame is a PING response. An endpoint MUST set this flag in PING responses. An endpoint MUST NOT respond to PING frames containing this flag. PING frames are not associated with any individual stream. If a PING frame is received with a stream identifier field value other than 0x0, the recipient MUST respond with a connection error of type PROTOCOL_ERROR. Receipt of a PING frame with a length field value other than 8 MUST be treated as a connection error of type PROTOCOL_ERROR.

The GOAWAY frame (type=0x7) informs the remote peer to stop creating streams on this connection. It can be sent from the client or the server. Once sent, the sender will ignore frames sent on new streams for the remainder of the connection. Receivers of a GOAWAY frame MUST NOT open additional streams on the connection, although a new connection can be established for new streams. The purpose of this frame is to allow an endpoint to gracefully stop accepting new streams (perhaps for a reboot or maintenance), while still finishing processing of previously established streams. There is an inherent race condition between an endpoint starting new streams and the remote sending a GOAWAY frame. To deal with this case, the GOAWAY contains the stream identifier of the last stream which was processed on the sending endpoint in this connection. If the receiver of the GOAWAY used streams that are newer than the indicated stream identifier, they were not processed by the sender and the receiver may treat the streams as though they had never been created at all (hence the receiver may want to re-create the streams later on a new connection). Endpoints SHOULD always send a GOAWAY frame before closing a connection so that the remote can know whether a stream has been partially processed or not. For example, if an HTTP client sends a POST at the same time that a server closes a connection, the client cannot know if the server started to process that POST request if the server does not send a GOAWAY frame to indicate where it stopped working. An endpoint might choose to close a connection without sending GOAWAY for misbehaving peers. After sending a GOAWAY frame, the sender can discard frames for new streams. However, any frames that alter connection state cannot be completely ignored. For instance, HEADERS, PUSH_PROMISE and CONTINUATION frames MUST be minimally processed to ensure a consistent compression state (see ); similarly DATA frames MUST be counted toward the connection flow control window.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X| Last-Stream-ID (31) | +-+-------------------------------------------------------------+ | Error Code (32) | +---------------------------------------------------------------+ | Additional Debug Data (*) | +---------------------------------------------------------------+

The GOAWAY frame does not define any flags. The GOAWAY frame applies to the connection, not a specific stream. The stream identifier MUST be zero. The last stream identifier in the GOAWAY frame contains the highest numbered stream identifier for which the sender of the GOAWAY frame has received frames on and might have taken some action on. All streams up to and including the identified stream might have been processed in some way. The last stream identifier is set to 0 if no streams were processed. Note: In this case, "processed" means that some data from the stream was passed to some higher layer of software that might have taken some action as a result. If a connection terminates without a GOAWAY frame, this value is effectively the highest stream identifier. On streams with lower or equal numbered identifiers that were not closed completely prior to the connection being closed, re-attempting requests, transactions, or any protocol activity is not possible (with the exception of idempotent actions like HTTP GET, PUT, or DELETE). Any protocol activity that uses higher numbered streams can be safely retried using a new connection. Activity on streams numbered lower or equal to the last stream identifier might still complete successfully. The sender of a GOAWAY frame might gracefully shut down a connection by sending a GOAWAY frame, maintaining the connection in an open state until all in-progress streams complete. The last stream ID MUST be 0 if no streams were acted upon. The GOAWAY frame also contains a 32-bit error code that contains the reason for closing the connection. Endpoints MAY append opaque data to the payload of any GOAWAY frame. Additional debug data is intended for diagnostic purposes only and carries no semantic value. Debug data MUST NOT be persistently stored, since it could contain sensitive information.

The WINDOW_UPDATE frame (type=0x9) is used to implement flow control. Flow control operates at two levels: on each individual stream and on the entire connection. Both types of flow control are hop by hop; that is, only between the two endpoints. Intermediaries do not forward WINDOW_UPDATE frames between dependent connections. However, throttling of data transfer by any receiver can indirectly cause the propagation of flow control information toward the original sender. Flow control only applies to frames that are identified as being subject to flow control. Of the frame types defined in this document, this includes only DATA frame. Frames that are exempt from flow control MUST be accepted and processed, unless the receiver is unable to assign resources to handling the frame. A receiver MAY respond with a stream error or connection error of type FLOW_CONTROL_ERROR if it is unable accept a frame.

0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |X| Window Size Increment (31) | +-+-------------------------------------------------------------+

The payload of a WINDOW_UPDATE frame is one reserved bit, plus an unsigned 31-bit integer indicating the number of bytes that the sender can transmit in addition to the existing flow control window. The legal range for the increment to the flow control window is 1 to 231 - 1 (0x7fffffff) bytes. The WINDOW_UPDATE frame does not define any flags. The WINDOW_UPDATE frame can be specific to a stream or to the entire connection. In the former case, the frame's stream identifier indicates the affected stream; in the latter, the value "0" indicates that the entire connection is the subject of the frame. WINDOW_UPDATE can be sent by a peer that has sent a frame bearing the END_STREAM flag. This means that a receiver could receive a WINDOW_UPDATE frame on a "half closed (remote)" or "closed" stream. A receiver MUST NOT treat this as an error, see . A receiver that receives a flow controlled frame MUST always account for its contribution against the connection flow control window, unless the receiver treats this as a connection error. This is necessary even if the frame is in error. Since the sender counts the frame toward the flow control window, if the receiver does not, the flow control window at sender and receiver can become different.

Flow control in HTTP/2.0 is implemented using a window kept by each sender on every stream. The flow control window is a simple integer value that indicates how many bytes of data the sender is permitted to transmit; as such, its size is a measure of the buffering capability of the receiver. Two flow control windows are applicable: the stream flow control window and the connection flow control window. The sender MUST NOT send a flow controlled frame with a length that exceeds the space available in either of the flow control windows advertised by the receiver. Frames with zero length with the END_STREAM flag set (for example, an empty data frame) MAY be sent if there is no available space in either flow control window. For flow control calculations, the 8 byte frame header is not counted. After sending a flow controlled frame, the sender reduces the space available in both windows by the length of the transmitted frame. The receiver of a frame sends a WINDOW_UPDATE frame as it consumes data and frees up space in flow control windows. Separate WINDOW_UPDATE frames are sent for the stream and connection level flow control windows. A sender that receives a WINDOW_UPDATE frame updates the corresponding window by the amount specified in the frame. A sender MUST NOT allow a flow control window to exceed 231 - 1 bytes. If a sender receives a WINDOW_UPDATE that causes a flow control window to exceed this maximum it MUST terminate either the stream or the connection, as appropriate. For streams, the sender sends a RST_STREAM with the error code of FLOW_CONTROL_ERROR code; for the connection, a GOAWAY frame with a FLOW_CONTROL_ERROR code. Flow controlled frames from the sender and WINDOW_UPDATE frames from the receiver are completely asynchronous with respect to each other. This property allows a receiver to aggressively update the window size kept by the sender to prevent streams from stalling.

When a HTTP/2.0 connection is first established, new streams are created with an initial flow control window size of 65535 bytes. The connection flow control window is 65535 bytes. Both endpoints can adjust the initial window size for new streams by including a value for SETTINGS_INITIAL_WINDOW_SIZE in the SETTINGS frame that forms part of the connection header. Prior to receiving a SETTINGS frame that sets a value for SETTINGS_INITIAL_WINDOW_SIZE, an endpoint can only use the default initial window size when sending flow controlled frames. Similarly, the connection flow control window is set to the default initial window size until a WINDOW_UPDATE frame is received. A SETTINGS frame can alter the initial flow control window size for all current streams. When the value of SETTINGS_INITIAL_WINDOW_SIZE changes, a receiver MUST adjust the size of all stream flow control windows that it maintains by the difference between the new value and the old value. A SETTINGS frame cannot alter the connection flow control window. A change to SETTINGS_INITIAL_WINDOW_SIZE could cause the available space in a flow control window to become negative. A sender MUST track the negative flow control window, and MUST NOT send new flow controlled frames until it receives WINDOW_UPDATE frames that cause the flow control window to become positive. For example, if the client sends 60KB immediately on connection establishment, and the server sets the initial window size to be 16KB, the client will recalculate the available flow control window to be -44KB on receipt of the SETTINGS frame. The client retains a negative flow control window until WINDOW_UPDATE frames restore the window to being positive, after which the client can resume sending.

A receiver that wishes to use a smaller flow control window than the current size can send a new SETTINGS frame. However, the receiver MUST be prepared to receive data that exceeds this window size, since the sender might send data that exceeds the lower limit prior to processing the SETTINGS frame. A receiver has two options for handling streams that exceed flow control limits: The receiver can immediately send RST_STREAM with FLOW_CONTROL_ERROR error code for the affected streams. The receiver can accept the streams and tolerate the resulting head of line blocking, sending WINDOW_UPDATE frames as it consumes data. If a receiver decides to accept streams, both sides MUST recompute the available flow control window based on the initial window size sent in the SETTINGS.

After a receiver reads in a frame that marks the end of a stream (for example, a data stream with a END_STREAM flag set), it MUST cease transmission of WINDOW_UPDATE frames for that stream. A sender is not obligated to maintain the available flow control window for streams that it is no longer sending on. Flow control can be disabled the entire connection using the SETTINGS_FLOW_CONTROL_OPTIONS setting. This setting ends all forms of flow control. An implementation that does not wish to perform flow control can use this in the initial SETTINGS exchange. Flow control cannot be enabled again once disabled. Any attempt to re-enable flow control - by sending a WINDOW_UPDATE or by clearing the bits on the SETTINGS_FLOW_CONTROL_OPTIONS setting - MUST be rejected with a FLOW_CONTROL_ERROR error code.

The CONTINUATION frame (type=0xA) is used to continue a sequence of header block fragments. Any number of CONTINUATION frames can be sent on an existing stream, as long as the preceding frame on the same stream is one of HEADERS, PUSH_PROMISE or CONTINUATION.

The CONTINUATION frame defines the following flags: Bit 1 being set indicates that this frame is the last that the endpoint will send for the identified stream. Setting this flag causes the stream to enter a "half closed" or "closed" state. The END_HEADERS bit indicates that this frame ends the sequence of header block fragments necessary to provide a complete set of headers. The payload for a complete header block is provided by a sequence that starts with a HEADERS or PUSH_PROMISE frame and zero or more CONTINUATION frames, terminated by a HEADERS, PUSH_PROMISE, or CONTINUATION frame with the END_HEADERS flag set. Once the sequence terminates, the payload of all frames in the sequence are concatenated and interpreted as a single block. A HEADERS, PUSH_PROMISE, or CONTINUATION frame without the END_HEADERS flag set MUST be followed by a CONTINUATION frame for the same stream. A receiver MUST treat the receipt of any other type of frame or a frame on a different stream as a connection error of type PROTOCOL_ERROR. The payload of a CONTINUATION frame contains a header block fragment. The CONTINUATION frame changes the connection state as defined in . CONTINUATION frames MUST be associated with a stream. If a CONTINUATION frame is received whose stream identifier field is 0x0, the recipient MUST respond with a connection error of type PROTOCOL_ERROR. header block fragments. A CONTINUATION frame MUST be preceded by one of HEADERS, PUSH_PROMISE or CONTINUATION frame. A recipient that observes violation of this rule MUST respond with a connection error of type PROTOCOL_ERROR.

Error codes are 32-bit fields that are used in RST_STREAM and GOAWAY frames to convey the reasons for the stream or connection error. Error codes share a common code space. Some error codes only apply to specific conditions and have no defined semantics in certain frame types. The following error codes are defined: The associated condition is not as a result of an error. For example, a GOAWAY might include this code to indicate graceful shutdown of a connection. The endpoint detected an unspecific protocol error. This error is for use when a more specific error code is not available. The endpoint encountered an unexpected internal error. The endpoint detected that its peer violated the flow control protocol. The endpoint received a frame after a stream was half closed. The endpoint received a frame that was larger than the maximum size that it supports. The endpoint refuses the stream prior to performing any application processing, see for details. Used by the endpoint to indicate that the stream is no longer needed. The endpoint is unable to maintain the compression context for the connection.

HTTP/2.0 is intended to be as compatible as possible with current web-based applications. This means that, from the perspective of the server business logic or application API, the features of HTTP are unchanged. To achieve this, all of the application request and response header semantics are preserved, although the syntax of conveying those semantics has changed. Thus, the rules from HTTP/1.1 (, , , , , and ) apply with the changes in the sections below.

A client sends an HTTP request on a new stream, using a previously unused stream identifier. A server sends an HTTP response on the same stream as the request. An HTTP request or response each consist of: a HEADERS frame; one contiguous sequence of zero or more CONTINUATION frames; zero or more DATA frames; and optionally, a contiguous sequence that starts with a HEADERS frame, followed by zero or more CONTINUATION frames. The last frame in the sequence bears an END_STREAM flag. Other frames MAY be interspersed with these frames, but those frames do not carry HTTP semantics. In particular, HEADERS frames (and any CONTINUATION frames that follow) other than the first and optional last frames in this sequence do not carry HTTP semantics. Trailing header fields are carried in a header block that also terminates the stream. That is, a sequence starting with a HEADERS frame, followed by zero or more CONTINUATION frames, that carries an END_STREAM flag on the last frame. Header blocks after the first that do not terminate the stream are not part of an HTTP request or response. An HTTP request/response exchange fully consumes a single stream. A request starts with the HEADERS frame that puts the stream into an "open" state and ends with a frame bearing END_STREAM, which causes the stream to become "half closed" for the client. A response starts with a HEADERS frame and ends with a frame bearing END_STREAM, which places the stream in the "closed" state.

For example, an HTTP GET request that includes request header fields and no body, is transmitted as a single contiguous sequence of HEADERS frames containing the serialized block of request header fields. The last HEADERS frame in the sequence has both the END_HEADERS and END_STREAM flag set:

+ END_STREAM Accept: image/jpeg + END_HEADERS :method = GET :scheme = https :host = example.org :path = /resource accept = image/jpeg ]]>

Similarly, a response that includes only response header fields is transmitted as a sequence of HEADERS frames containing the serialized block of response header fields. The last HEADERS frame in the sequence has both the END_HEADERS and END_STREAM flag set:

+ END_STREAM + END_HEADERS :status = 204 content-length: 0 ]]>

An HTTP POST request that includes request header fields and payload data is transmitted as one HEADERS frame, followed by zero or more CONTINUATION frames, containing the request headers followed by one or more DATA frames, with the last CONTINUATION (or HEADERS) frame having the END_HEADERS flag set and the final DATA frame having the END_STREAM flag set:

- END_STREAM Content-Type: image/jpeg + END_HEADERS Content-Length: 123 :method = POST :scheme = https {binary data} :host = example.org :path = /resource content-type = image/jpeg content-length = 123 DATA + END_STREAM {binary data} ]]>

A response that includes header fields and payload data is transmitted as a HEADERS frame, followed by zero or more CONTINUATION frames, followed by one or more DATA frames, with the last DATA frame in the sequence having the END_STREAM flag set:

- END_STREAM Content-Length: 123 + END_HEADERS :status = 200 {binary data} content-type = image/jpeg content-length = 123 DATA + END_STREAM {binary data} ]]>

Trailing header fields are sent as a header block after both the request or response header block and all the DATA frames have been sent. The sequence of HEADERS/CONTINUATION frames that bears the trailers includes a terminal frame that has both END_HEADERS and END_STREAM flags set.

- END_STREAM Content-Length: 123 + END_HEADERS TE: trailers :status = 200 123 content-type = image/jpeg {binary data} content-length = 123 0 Foo: bar DATA - END_STREAM {binary data} HEADERS + END_STREAM + END_HEADERS foo: bar ]]>

HTTP/2.0 request and response header fields carry information as a series of key-value pairs. This includes the target URI for the request, the status code for the response, as well as HTTP header fields. HTTP header field names are strings of ASCII characters that are compared in a case-insensitive fashion. Note that header compression could cause case information to be lost. The semantics of HTTP header fields are not altered by this specification, though header fields relating to connection management or request framing are no longer necessary. An HTTP/2.0 request MUST NOT include any of the following header fields: Connection, Host, Keep-Alive, Proxy-Connection, TE, Transfer-Encoding, and Upgrade. A server MUST treat the presence of any of these header fields as a stream error of type PROTOCOL_ERROR.

HTTP/2.0 defines a number of headers starting with a ':' character that carry information about the request target: The :method header field includes the HTTP method (). The :scheme header field includes the scheme portion of the target URI (). The :host header field includes the authority portion of the target URI (). The :path header field includes the path and query parts of the target URI (the path-absolute production from and optionally a '?' character followed by the query production, see and ). This field MUST NOT be empty; URIs that do not contain a path component MUST include a value of '/', unless the request is an OPTIONS request for '*', in which case the :path header field MUST include '*'. All HTTP/2.0 requests MUST include exactly one valid value for all of these header fields. An intermediary MUST ensure that requests that it forwards are correct. A server MUST treat the absence of any of these header fields, presence of multiple values, or an invalid value as a stream error of type PROTOCOL_ERROR. HTTP/2.0 does not define a way to carry the version identifier that is included in the HTTP/1.1 request line. All HTTP Requests that include a body can include a content-length header field. If a server receives a request where the sum of the DATA frame payload lengths does not equal the value of the content-length header field, the server MUST return a 400 (Bad Request) error.

A single :status header field is defined that carries the HTTP status code field (see ). This header field MUST be included in all responses. An intermediary MUST ensure that it does not forward responses with absent or invalid values. A client MUST treat the absence of the :status" header field, the presence of multiple values, or an invalid value as a stream error of type PROTOCOL_ERROR. HTTP/2.0 does not define a way to carry the version or reason phrase that is included in an HTTP/1.1 status line.

In HTTP/1.1, an HTTP client is unable to retry a non-idempotent request when an error occurs, because there is no means to determine the nature of the error. It is possible that some server processing occurred prior to the error, which could result in undesirable effects if the request were reattempted. HTTP/2.0 provides two mechanisms for providing a guarantee to a client that a request has not been processed: The GOAWAY frame indicates the highest stream number that might have been processed. Requests on streams with higher numbers are therefore guaranteed to be safe to retry. The REFUSED_STREAM error code can be included in a RST_STREAM frame to indicate that the stream is being closed prior to any processing having occurred. Any request that was sent on the reset stream can be safely retried. In both cases, clients MAY automatically retry all requests, including those with non-idempotent methods. A server MUST NOT indicate that a stream has not been processed unless it can guarantee that fact. If frames that are on a stream are passed to the application layer for any stream, then REFUSED_STREAM MUST NOT be used for that stream, and a GOAWAY frame MUST include a stream identifier that is greater than or equal to the given stream identifier. In addition to these mechanisms, the PING frame provides a way for a client to easily test a connection. Connections that remain idle can become broken as some middleboxes (for instance, network address translators, or load balancers) silently discard connection bindings. The PING frame allows a client to safely test whether a connection is still active without sending a request.

HTTP/2.0 enables a server to pre-emptively send (or "push") multiple associated resources to a client in response to a single request. This feature becomes particularly helpful when the server knows the client will need to have those resources available in order to fully process the originally requested resource. Pushing additional resources is optional, and is negotiated only between individual endpoints. For instance, an intermediary could receive pushed resources from the server but is not required to forward those on to the client. How to make use of the pushed resources is up to that intermediary. Equally, the intermediary might choose to push additional resources to the client, without any action taken by the server.

Server push is semantically equivalent to a server responding to a request. The PUSH_PROMISE frame, or frames, sent by the server includes a header block that contains a complete set of request headers that the server attributes to the request. It is not possible to push a response to a request that includes a request body. Pushed resources are always associated with an explicit request from a client. The PUSH_PROMISE frames sent by the server are sent on the stream created for the original request. The PUSH_PROMISE frame includes a promised stream identifier, chosen from the stream identifiers available to the server (see ). The header fields in PUSH_PROMISE and any subsequent CONTINUATION frames MUST be a valid and complete set of request headers. The server MUST include a method in the :method header field that is safe (see ). If a client receives a PUSH_PROMISE that does not include a complete and valid set of header fields, or the :method header field identifies a method that is not safe, it MUST respond with a stream error of type PROTOCOL_ERROR. The server SHOULD send PUSH_PROMISE () frames prior to sending any frames that reference the promised resources. This avoids a race where clients issue requests for resources prior to receiving any PUSH_PROMISE frames. For example, if the server receives a request for a document containing embedded links to multiple image files, and the server chooses to push those additional images to the client, sending push promises before the DATA frames that contain the image links ensure that the client is able to see the promises before discovering the resources. Similarly, if the server pushes resources referenced by the header block (for instance, in Link header fields), sending the push promises before sending the header block ensures that clients do not request those resources. PUSH_PROMISE frames MUST NOT be sent by the client. PUSH_PROMISE frames can be sent by the server on any stream that was opened by the client. They MUST be sent on a stream that is in either the "open" or "half closed (remote)" to the server. PUSH_PROMISE frames are interspersed with the frames that comprise a response, though they cannot be interspersed with HEADERS and CONTINUATION frames that comprise a single header block.

After sending the PUSH_PROMISE frame, the server can begin delivering the pushed resource as a response on a server-initiated stream that uses the promised stream identifier. The server uses this stream to transmit an HTTP response, using the same sequence of frames as defined in . This stream becomes "half closed" to the client after the initial HEADERS frame is sent. Once a client receives a PUSH_PROMISE frame and chooses to accept the pushed resource, the client SHOULD NOT issue any requests for the promised resource until after the promised stream has closed. If the client determines, for any reason, that it does not wish to receive the pushed resource from the server, or if the server takes too long to begin sending the promised resource, the client can send an RST_STREAM frame, using either the CANCEL or REFUSED_STREAM codes, and referencing the pushed stream's identifier. A client can use the SETTINGS_MAX_CONCURRENT_STREAMS setting to limit the number of resources that can be concurrently pushed by a server. Advertising a SETTINGS_MAX_CONCURRENT_STREAMS value of zero disables server push by preventing the server from creating the necessary streams. This does not prohibit a server from sending PUSH_PROMISE frames; clients need to reset any promised streams that are not wanted. Clients receiving a pushed response MUST validate that the server is authorized to push the resource using the same-origin policy (). For example, a HTTP/2.0 connection to example.com is generally Ed: weaselly use of "generally", needs better definition not permitted to push a response for www.example.org.

This section outlines attributes of the HTTP protocol that improve interoperability, reduce exposure to known security vulnerabilities, or reduce the potential for implementation variation.

HTTP/2.0 connections are persistent. For best performance, it is expected clients will not close connections until it is determined that no further communication with a server is necessary (for example, when a user navigates away from a particular web page), or until the server closes the connection. Clients SHOULD NOT open more than one HTTP/2.0 connection to a given origin () concurrently. A client can create additional connections as replacements, either to replace connections that are near to exhausting the available stream identifiers, or to replace connections that have encountered errors. Servers are encouraged to maintain open connections for as long as possible, but are permitted to terminate idle connections if necessary. When either endpoint chooses to close the transport-level TCP connection, the terminating endpoint MUST first send a GOAWAY () frame so that both endpoints can reliably determine whether previously sent frames have been processed and gracefully complete or terminate any necessary remaining tasks.

Implementations of HTTP/2.0 MUST support TLS 1.1. The working group intends to require at least the use of TLS 1.2 prior to publication of this document; negotiating TLS 1.1 is permitted to enable the creation of interoperable implementations of early drafts. The TLS implementation MUST support the Server Name Indication (SNI) extension to TLS. HTTP/2.0 clients MUST indicate the target domain name when negotiating TLS. A server that receives a TLS handshake that does not include either TLS 1.1 or SNI, MUST NOT negotiate HTTP/2.0. Removing HTTP/2.0 protocols from consideration could result in the removal of all protocols from the set of protocols offered by the client. This causes protocol negotiation failure, as described in Section 3.2 of . Implementations are encouraged not to negotiate TLS cipher suites with known vulnerabilities, such as .

Frames used for HTTP messages MUST NOT exceed 214-1 (16383) octets in length, not counting the 8 octet frame header. An endpoint MUST treat the receipt of a larger frame as a FRAME_TOO_LARGE error (see ).

Clients MUST support gzip compression for HTTP response bodies. Regardless of the value of the accept-encoding header field, a server MAY send responses with gzip or deflate encoding. A compressed response MUST still bear an appropriate content-encoding header field.

This specification uses the same-origin policy () to determine whether an origin server is permitted to provide content. A server that is contacted using TLS is authenticated based on the certificate that it offers in the TLS handshake (see ). A server is considered authoritative for an "https" resource if it has been successfully authenticated for the domain part of the origin of the resource that it is providing. A server is considered authoritative for an "http" resource if the connection is established to a resolved IP address for the domain in the origin of the resource. A client MUST NOT use, in any way, resources provided by a server that is not authoritative for those resources.

When using TLS, we believe that HTTP/2.0 introduces no new cross-protocol attacks. TLS encrypts the contents of all transmission (except the handshake itself), making it difficult for attackers to control the data which could be used in a cross-protocol attack. Issue: This is no longer true

Pushed resources are responses without an explicit request; the request for a pushed resource is synthesized from the request that triggered the push, plus resource identification information provided by the server. Request header fields are necessary for HTTP cache control validations (such as the Vary header field) to work. For this reason, caches MUST inherit request header fields from the associated stream for the push. This includes the Cookie header field. Caching resources that are pushed is possible, based on the guidance provided by the origin server in the Cache-Control header field. However, this can cause issues if a single server hosts more than one tenant. For example, a server might offer multiple users each a small portion of its URI space. Where multiple tenants share space on the same server, that server MUST ensure that tenants are not able to push representations of resources that they do not have authority over. Failure to enforce this would allow a tenant to provide a representation that would be served out of cache, overriding the actual representation that the authoritative tenant provides. Pushed resources for which an origin server is not authoritative are never cached or used.

HTTP/2.0 aims to keep connections open longer between clients and servers in order to reduce the latency when a user makes a request. The maintenance of these connections over time could be used to expose private information. For example, a user using a browser hours after the previous user stopped using that browser may be able to learn about what the previous user was doing. This is a problem with HTTP in its current form as well, however the short lived connections make it less of a risk.

This document establishes registries for frame types, error codes and settings. These new registries are entered in a new "Hypertext Transfer Protocol (HTTP) 2.0 Parameters" section. This document also registers the HTTP2-Settings header field for use in HTTP.

This document establishes a registry for HTTP/2.0 frame types. The "HTTP/2.0 Frame Type" registry operates under the "IETF Review" policy. Frame types are an 8-bit value. When reviewing new frame type registrations, special attention is advised for any frame type-specific flags that are defined. Frame flags can interact with existing flags and could prevent the creation of globally applicable flags. Initial values for the "HTTP/2.0 Frame Type" registry are shown in . Frame TypeNameFlagsSection 0DATAEND_STREAM(1) 1HEADERSEND_STREAM(1), END_HEADERS(4), PRIORITY(8) 2PRIORITY- 3RST_STREAM- 4SETTINGS- 5PUSH_PROMISEEND_PUSH_PROMISE(1) 6PINGPONG(1) 7GOAWAY- 9WINDOW_UPDATE- 10CONTINUATIONEND_STREAM(1), END_HEADERS(4)

This document establishes a registry for HTTP/2.0 error codes. The "HTTP/2.0 Error Code" registry manages a 32-bit space. The "HTTP/2.0 Error Code" registry operates under the "Expert Review" policy. Registrations for error codes are required to include a description of the error code. An expert reviewer is advised to examine new registrations for possible duplication with existing error codes. Use of existing registrations is to be encouraged, but not mandated. New registrations are advised to provide the following information: The 32-bit error code value. A name for the error code. Specifying an error code name is optional. A description of the conditions where the error code is applicable. An optional reference for a specification that defines the error code. An initial set of error code registrations can be found in .

This document establishes a registry for HTTP/2.0 settings. The "HTTP/2.0 Settings" registry manages a 24-bit space. The "HTTP/2.0 Settings" registry operates under the "Expert Review" policy. Registrations for settings are required to include a description of the setting. An expert reviewer is advised to examine new registrations for possible duplication with existing settings. Use of existing registrations is to be encouraged, but not mandated. New registrations are advised to provide the following information: The 24-bit setting value. A name for the setting. Specifying a name is optional. Any setting-specific flags that apply, including their value and semantics. A description of the setting. This might include the range of values, any applicable units and how to act upon a value when it is provided. An optional reference for a specification that defines the setting. An initial set of settings registrations can be found in .

This section registers the HTTP2-Settings header field in the Permanent Message Header Field Registry. HTTP2-Settings http standard IETF of this document This header field is only used by an HTTP/2.0 client for Upgrade-based negotiation.

This document includes substantial input from the following individuals: Adam Langley, Wan-Teh Chang, Jim Morrison, Mark Nottingham, Alyssa Wilk, Costin Manolache, William Chan, Vitaliy Lvin, Joe Chan, Adam Barth, Ryan Hamilton, Gavin Peters, Kent Alstad, Kevin Lindsay, Paul Amer, Fan Yang, Jonathan Leighton (SPDY contributors). Gabriel Montenegro and Willy Tarreau (Upgrade mechanism) William Chan, Salvatore Loreto, Osama Mazahir, Gabriel Montenegro, Jitu Padhye, Roberto Peon, Rob Trace (Flow control) Mark Nottingham, Julian Reschke, James Snell, Jeff Pinner (Substantial editorial contributions)

University of Southern California (USC)/Information Sciences Institute Harvard University

sob@harvard.edu

Adobe Systems Incorporated

fielding@gbiv.com

greenbytes GmbH

julian.reschke@greenbytes.de

Adobe Systems Incorporated

fielding@gbiv.com

World Wide Web Consortium

ylafon@w3.org

greenbytes GmbH

julian.reschke@greenbytes.de

Adobe Systems Incorporated

fielding@gbiv.com

Akamai

mnot@mnot.net

greenbytes GmbH

julian.reschke@greenbytes.de

Adobe Systems Incorporated

fielding@gbiv.com

greenbytes GmbH

julian.reschke@greenbytes.de

Nine by Nine

GK-IETF@ninebynine.org

BEA Systems

mnot@pobox.com

HP Labs

JeffMogul@acm.org

Added CONTINUATION frame for HEADERS and PUSH_PROMISE. PUSH_PROMISE is no longer implicitly prohibited if SETTINGS_MAX_CONCURRENT_STREAMS is zero. Push expanded to allow all safe methods without a request body. Clarified the use of HTTP header fields in requests and responses. Prohibited HTTP/1.1 hop-by-hop header fields. Requiring that intermediaries not forward requests with missing or illegal routing :-headers. Clarified requirements around handling different frames after stream close, stream reset and GOAWAY. Added more specific prohibitions for sending of different frame types in various stream states. Making the last received setting value the effective value. Clarified requirements on TLS version, extension and ciphers.

Committed major restructuring atrocities. Added reference to first header compression draft. Added more formal description of frame lifecycle. Moved END_STREAM (renamed from FINAL) back to HEADERS/DATA. Removed HEADERS+PRIORITY, added optional priority to HEADERS frame. Added PRIORITY frame.

Added continuations to frames carrying header blocks. Replaced use of "session" with "connection" to avoid confusion with other HTTP stateful concepts, like cookies. Removed "message". Switched to TLS ALPN from NPN. Editorial changes.

Added IANA considerations section for frame types, error codes and settings. Removed data frame compression. Added PUSH_PROMISE. Added globally applicable flags to framing. Removed zlib-based header compression mechanism. Updated references. Clarified stream identifier reuse. Removed CREDENTIALS frame and associated mechanisms. Added advice against naive implementation of flow control. Added session header section. Restructured frame header. Removed distinction between data and control frames. Altered flow control properties to include session-level limits. Added note on cacheability of pushed resources and multiple tenant servers. Changed protocol label form based on discussions.

Changed title throughout. Removed section on Incompatibilities with SPDY draft#2. Changed INTERNAL_ERROR on GOAWAY to have a value of 2 . Replaced abstract and introduction. Added section on starting HTTP/2.0, including upgrade mechanism. Removed unused references. Added flow control principles based on .

Adopted as base for draft-ietf-httpbis-http2. Updated authors/editors list. Added status note.